WS-X45-SUP8-E is the Cisco Catalyst 4500E Supervisor 8-E helps to enable the Cisco Unified Access solution on the world's most widely deployed modular access switch—Cisco Catalyst 4500E. It brings the best of wired and wireless technologies together while preserving investment on existing wired infrastructure. It supports full wireless LAN controller functionality and common features across wired and wireless networks.
Notice that WS-X45-SUP8-E= is similar with WS-X45-SUP8-E, except that WS-X45-SUP8-E= is a spare one.
Figure 1. WS-X45-SUP8-E Appearance.
Centralized switching capacity
Up to 928 Gbps
Wireless Termination Capacity
Up to 20 Gbps (software Roadmap)
Per-slot switching capacity
250 Mpps for IPv4
125 Mpps for IPv6
IPv4 routing entries
IPv6 routing entries
Quad core; 2.0 GHz
Synchronous dynamic RAM (SDRAM)
Nonvolatile RAM (NVRAM)
Security and QoS hardware entries
Cisco Network Admission Control (NAC) and Dynamic Host
Configuration Protocol (DHCP) snooping entries
Dynamic Host Configuration Protocol (DHCP) Snooping Entries
Address Resolution Protocol (ARP) entries
Spanning Tree Protocol instances
Switched virtual interfaces (SVIs)
Switched Port Analyzer (SPAN)
Maximum of 8 bi-directional sessions
Figure 2. WS-X45-SUP8-E can be installed in the Catalyst 4500 switch Chassis. The Supervisor installed in the switch is only for reference.
Figure 3. WS-X45-SUP8-E Front view.
①USB Ports ②Console Port ③10/100/1000 MGT Port ④Secure Digital Port ⑤4 × 1G/10G Uplinks SFP/SFP+
Supported Line Cards and Modules
Table 2. Recommended Cisco Catalyst 4500E Series Line Cards and Modules.
Cisco Catalyst 4500E Series, 48-port 802.3af PoE, 802.3at PoEP, and UPoE 10/100/1000
Cisco Catalyst 4500E Series, 48-port PoE 802.3at 10/100/1000 (RJ-45)
Cisco Catalyst 4500E Series, 12-port 10 Gigabit Ethernet (SFP+)
Cisco Catalyst 4500E Series 48-port Gigabit Ethernet (SFP)
Cisco Catalyst 4500E Series 24-port Gigabit Ethernet (SFP)
Cisco Catalyst 4500E Series 12-port Gigabit Ethernet (SFP)
Cisco Catalyst 4500E Series, 48-port Premium PoE 10/100/1000 (RJ-45)
Cisco Catalyst 4500E Series, 48-port 10/100/1000 (RJ-45)
Cisco Catalyst 4500E Series, 6-port 10 Gigabit Ethernet (X2)
Cisco Catalyst 4500E Series, 24-port Gigabit Ethernet (SFP)
Cisco Catalyst 4500E Series 12-port Gigabit Ethernet (SFP)
Get More Information
Do you have any question about the WS-X45-SUP8-E?
Contact us now via Live Chat or email@example.com.
The Supervisor Engine 8-E is supported on the Catalyst 4503-E, Catalyst 4506-E, Catalyst 4507R+E, Catalyst 4510R+E, Catalyst 4507R-E1, and Catalyst 4510R-E switch chassis.
Refer to your software release notes for the latest software release requirements
Chassis slot restrictions
Catalyst 4503-E: Slot 1 only
Catalyst 4506-E: Slot 1 only
Catalyst 4507R+E: Slot 3 and slot 4 (redundant supervisor engines supported)
Catalyst 4510R+E: Slot 5 and slot 6 (redundant supervisor engines supported)
Catalyst 4507R-E: Slot 3 and 4 (redundant supervisor engines supported)
Catalyst 4510R-E: Slot 5 and 6 (redundant supervisor engines supported)
Bandwidth per slot
The status LED indicates the current health of the supervisor engine and the current software state.
The RESET switch is used to reset and restart the switch.
Note The reset switch is recessed into the front panel; you need to use a paper clip or other small, pointed object to press the RESET switch.
DC STATUS LED
The DC status LED indicates the current status of the wireless daughter card.
UID switch and LED
A combination push button switch and LED indicator. The blue LED can be turned on either by pressing the UID switch on the front panel or through software. The main purpose of the beacon LED is to enable identification from a remote location during configuration or troubleshooting. The ability to turn on/off the LED by pressing a switch allows you to walk to the other side of a fully populated rack and identify the switch. Pressing the blue beacon LED switch toggles the beacon LED on and off.
USB ports are supported with hardware revision 1.1 or higher.
This is a 10/100/1000 port that uses an RJ-45 connector. The console port allows you to access the switch either locally (with a console terminal) or through a modem (remote). The port has an RJ-45 connector. The console port allows you to perform the following functions:
Configure the switch from the CLI
Monitor network statistics and errors
Configure SNMP agent parameters
The 10/100/1000 MGT port has a link LED associated with it..
10/100/1000 MGT port
The Ethernet management port is a Layer 3 host port to which you can connect a PC. You can use the Ethernet management port instead of the switch console port for network management. When managing a switch, connect the PC to the Ethernet management port on a Catalyst 4500 E-series switch.
Note When connecting a PC to the Ethernet management port, you must assign an IP address.
SECURE DIGITAL slot
A standard Secure Data (SD) memory card interface is provided on the front panel
The SD LED indicates the current status of the SD memory card slot.
ACTIVE SUP LED
The active supervisor engine LED indicates whether the supervisor engine is active or in standby mode in redundant supervisor engine configurations.
Eight LEDs indicate (as an approximate percentage) the current traffic load over the backplane.
1G/10G UPLINKS (SFP/SFP+) ports
The Supervisor Engine 8-E has eight 1-G or 10-G ports that use either SFP transceivers or SFP+ transceivers.
Uplink port LEDs
The Uplink port LEDs display status and activity of the uplink ports.
Supervisor Engine 8-E Front Panel LEDs
Indicates the status of the supervisor engine.
Green—All diagniostic tests have passed.
Orange—System boot or a diagnostic test is in progress.
Red—A diagnostic test failed.
Off—The supervisor engine is disabled or is not powered up.
Indicates the status of the wireless daughter card.
Flashing green—The daughter card is booting.
Flashing orange—The system is waiting user input.
Orange—A diagnostic test failed.
Off—No power to the daughter card.
Indicates the status of the 10/100/1000BASE-T Ethernet management port.
Green—The link is operational.
Off—No signal is detected or there is a link configuration failure or the link is disabled by user.
Indicates the status of the secure digital port.
Green—SD card is inserted.
Off—SD card has been removed, or the SD card is bad.
Indicates whether the supervisor engine is active or standby.
Green—Supervisor engine is active (in redundant supervisor engine configurations)
Off—Supervisor engine is in standby mode (in redundant supervisor engine configurations)
When the switch is operational, the eight utilization LEDs indicate the current traffic load over the backplane as an approximate percentage value. Each LED lit green indicates approximately 12.5 percent of load.
Uplink port status
Indicates the status of the uplink port.
Green—The link is operational.
Orange—The link is disabled by user.
Flashing orange—The power-on self-test indicates a faulty port.
Off—No signal is detected or there is a link configuration failure.
Uplink port active
Three LEDs on the front panel show the uplink port activity.
1-2 ACTIVE indicates ports 1 and 2 are active
3-4 ACTIVE indicates ports 3 and 4 are active
5-8 ACTIVE indicates ports 5 through 8 are active
In standalone supervisor engine configurations, all eight uplink ports are active; all of the ACTIVE LEDs are lit green.
In redundant supervisor engine configurations, only the 1-2 ACTIVE LED and 3-4 ACTIVE LED are lit green.
Are the Cisco Catalyst 4500E Supervisor Engine 8-E, 7-E, and 7L-E supported in classic chassis?
No. The Cisco Catalyst 4500E Supervisor Engine 8-E, 7-E, and 7L-E work only with E-Series chassis.
What licenses are required to enable wireless termination capability on available on an Cisco 4500E Supervisor Engine 8-E?
No additional license on top of IP Base is required to enable wireless termination. Note that this feature is targeted for 1HCY14.
What licenses are required to enable wireless controller capability on available on a Catalyst 4500E Supervisor Engine 8-E?
In addition to IP Base or Enterprise Services, the customer would need to buy access point licenses to enable wireless controller functionality. Note that this feature and license are targeted for 1HCY14.
- Shipping & Payment
Cargo will be delivered within 1 day after payment arrived. Tracking Number will be offered once delivery done.
Delivery Options Estimated Delivery Time DHL 2-4 business days Fedex 2-4 business days Hong Kong EMS 5-10 business days Hong Kong Air Parcel 10-20 business days By Sea 10-20 business days
Above mentioned information are just for your reference only,we will keep you posted for the tracking delivery schedule.There are two delivery options available for by air and by sea:
Deliver to port:
Router-switch.com is responsible for transporting goods to port. All subsequent customs and transportation fees are the
responsibility of the buyer. Router-switch will recommend trustworthy local freight forwarders to you.Router-switch.com can facilitate the progress under buyer's permission and at buyer's expense.
Deliver to door:
Router-switch.com will quote all destination charge prior once we have confirmed order.
Router-switch.com is responsible for transporting goods to door after you have made the payment.
Paypal Master Card Visa Discover American
JCB Wire Transfer eCheck WestUnion
100% Low Price Guarantee:
Router-switch.com provides high-quality products at low wholesale prices
100% Quality Assurance:
All items are ORIGINAL and GENUINE only.
Item conditions are "New Sealed" or "Used / Refurbished".
Used & refurbished items are fully tested with good conditions by Cisco-certified Engineers.
Free CCIE Technical Support:
Our FREE Cisco CCIE Expert Consultancy Support is over the phone, by chat, by email or by login remotely.
100% Money Back Guarantee:
You can contact our customer service team to exchange or return any product that you bought from us.
Flexible Secure Payment & Shipment:
Verified authorization: Mcafee Secure, VeriSign Secured
Return Material Authorization (RMA) Process
Standard Hardware Warranty Policy:
Original new sealed Cisco product: 1 Year
Used Cisco product: 3 Month
The Support Contacts:
If your Cisco products failed, you must contact your sales representative to verify product failure. If the problem still can't correct by remote support methods i.e. email or phone support, the RMA procedure will issue.
Standard ServicesBranch Offices : Hong Kong | USA | UKHong Kong WarehouseShenzhen WarehouseQuality CheckingPackagingShipping