Catalyst 6500 Enhanced 9-slot Chassis (Vertical), No PS, Fan

Catalyst 6500 Enhanced 9-slot chassis, 15RU, no PS, no Fan Tray

Catalyst 6500 Enhanced 9-slot chassis, 15RU, no PS, no Fan Tray

Catalyst 6500 Enhanced 6-slot chassis, 12RU, no PS, no Fan Tray

Catalyst 6500 Enhanced 4-slot chassis, 5RU, no PS, no Fan Tray

Catalyst 6500 Enhanced 3-slot chassis, 4RU, no PS, no Fan Tray

The Cisco 7609 Router is a high-performance router deployed at the network edge, where performance, IP services, redundancy, and fault resiliency are critical. Combined with a central route processor and forwarding engine, the Cisco 7609 Router provides 30-Mpps forwarding rates and up to 256 Gbps of total throughput. This versatile Cisco 7600 Series system scales WAN connectivity from OC-48/STM-16 to DS0 and LAN connectivity from 10 Gigabit Ethernet through 10 Mbps Ethernet. The Cisco 7609 delivers these capabilities while implementing high-touch, hardware-accelerated IP services through the Cisco Parallel Express Forwarding (PXF) network processor.

7609-RSP720CXL-R data sheet
Product Description	Cisco 7609 - router - with 2 x Cisco 7600 Series Route Switch Processor 720 with PFC-3CXL
Manufacturer	Cisco Systems, Inc
Manufacturer Part Number	7609-RSP720CXL-R
Product Type	Router
Form Factor	Plug-in module - modular - 21U
Dimensions (WxDxH)	43.1 cm x 53.3 cm x 93.3 cm
Weight	54.9 kg
Processor	PowerPC 1.2 GHz
DRAM Memory	3 GB (installed) / 6 GB (max)
Routing Protocol	OSPF, RIP, BGP-4, IS-IS, IGMP, PIM-SM, PIM-DM
Data Link Protocol	Ethernet, Fast Ethernet, Gigabit Ethernet
Network / Transport Protocol	TCP/IP, ICMP/IP
Features	Layer 3 switching, Layer 2 switching, dynamic IP address assignment , DHCP support, MPLS support, VLAN support, IGMP snooping, traffic shaping, DoS attack prevention, Access Control List (ACL) support, Quality of Service (QoS)
Compliant Standards	IEEE 802.1x
Bundled with	2 x Cisco 7600 Series Route Switch Processor 720 with PFC-3CXL

The Cisco 7200 Series VPN bundles offer specific hardware configurations that are optimized for site-to-site VPN applications and network topologies, while simultaneously setting the benchmark for hardware configuration flexibility, upgradeability, and investment protection.K8 VPN bundles support cryptographic keys less than 64 bits in size

7204VXR/400 data sheet
Product Description	Cisco 7204 VXR VPN Bundle - router - with Cisco 7200 Series Network Processing Engine NPE-400
Manufacturer	Cisco Systems, Inc
Manufacturer Part Number	7204VXR/400
Product Type	Router
Form Factor	Rack-mountable - modular
Dimensions (WxDxH)	42.7 cm x 43.2 cm x 13.3 cm
Processor	RM7000A 350 MHz
DRAM Memory	256 MB
Data Link Protocol	Ethernet, Fast Ethernet
Network / Transport Protocol	IPSec
Features	Cisco IOS , VPN support, VPN acceleration capability
Power	AC 120/230 V ( 50/60 Hz )
Bundled with	Cisco 7200 Series Network Processing Engine NPE-400

With processing speeds up to 2 million packets per second, port- and service adapters ranging from NxDS0 to Gigabit Ethernet, and OC-3 as well as an unparalleled number of high-touch IP services, the Cisco 7200 VXR series is the ideal Services Aggregation WAN/MAN edge device for enterprises and service providers.Increasingly, business applications and services affect aggregation requirements and router-integrated services across the WAN and metropolitan-area network (MAN)-in both the branch office and headquarters. Consequently, to continue to meet the increasing need for performance for integrated services at the branch office and headquarters and to maintain exceptional value and flexibility, Cisco Systems introduces the newest processor for the Cisco 7200VXR Series-the Cisco 7200VXR NPE-G2 Network Processing Engine The Cisco NPE-G2 addresses the demand for performance and flexibility by further increasing its processing capacity and enabling the latest Cisco IOS Software features.

7206VXR/NPE-G2 data sheet
Product Description	Cisco 7206 VXR with NPE-G2 - router
Manufacturer	Cisco Systems, Inc
Manufacturer Part Number	7206VXR/NPE-G2
Product Type	Router
Form Factor	Rack-mountable - modular
Dimensions (WxDxH)	42.7 cm x 43.2 cm x 13.3 cm
DRAM Memory	1 GB DDR SDRAM
Flash Memory	256 MB
Routing Protocol	OSPF, IGRP, RIP, IS-IS, BGP, EIGRP, HSRP
Data Link Protocol	Ethernet, Fast Ethernet, Gigabit Ethernet
Network / Transport Protocol	TCP/IP, UDP/IP, PPPoA
Remote Management Protocol	SNMP, Telnet, HTTP
Features	Cisco IOS , flow control, modular design, full duplex capability, Layer 2 switching, auto-sensing per device, DHCP support, VPN support, BOOTP support, ARP support, MPLS support, VLAN support, manageable, IPv6 support
Compliant Standards	IEEE 802.1Q
Power	AC 120/230 V ( 50/60 Hz )

The Cisco 7201 Series Router is a compact, high-performance 1-rack-unit (1RU) router coupled with a broad set of interfaces and Cisco IOS Software features, making it ideal for both service providers and enterprise applications. The Cisco 7201 addresses the demand for performance and flexibility by further increasing its processing capacity and enabling the latest Cisco IOS Software features.

CISCO7201 data sheet
Product Description	Cisco 7201 - router
Manufacturer	Cisco Systems, Inc
Manufacturer Part Number	CISCO7201
Product Type	Router
Form Factor	External - modular - 1U
Dimensions (WxDxH)	48.3 cm x 42.9 cm x 4.4 cm
Weight	7.5 kg
Processor	1 x Motorola PowerPC 7448 1.67 GHz
DRAM Memory	1 GB (installed) / 2 GB (max) - DDR SDRAM
Flash Memory	256 MB (installed) / 256 MB (max)
Routing Protocol	HSRP
Data Link Protocol	Ethernet, Fast Ethernet, Gigabit Ethernet
Features	NAT support, load balancing, MPLS support, IPv6 support, Access Control List (ACL) support, Quality of Service (QoS)

Enterprise and service provider customers continue to drive the need for optimizing operational and management costs, simplifying network management and increasing revenue opportunities. The Cisco 7200 addresses these requirements by collapsing functions previously performed by separate devices into a single, cost-effective platform. Through functional integration, the Cisco 7200 high-performance multifunction platform provides a single, cost-effective platform.The Cisco 7200 series delivers exceptional price/performance to meet the requirements of both enterprise and service providers. With its combination of scalable performance, density, and low per-port pricing, the Cisco 7200 allows network-layer capabilities to be extended to a much wider range of network configurations and environments. Customers can now gain the advantages of high-performance network-layer switching and services, including security, QoS, and traffic management to more locations throughout the network.

CISCO7206VXR data sheet
Product Description	Cisco 7206 VXR - modular expansion base
Manufacturer	Cisco Systems, Inc
Manufacturer Part Number	CISCO7206VXR
Product Type	Modular expansion base
Form Factor	External - modular
Dimensions (WxDxH)	42.7 cm x 43.2 cm x 13.3 cm
Features	Modular design
Power	AC 120/230 V ( 50/60 Hz )

Enterprise and service provider customers continue to drive the need for optimizing operational and management costs, simplifying network management and increasing revenue opportunities. The Cisco 7200 addresses these requirements by collapsing functions previously performed by separate devices into a single, cost-effective platform. Through functional integration, the Cisco 7200 high-performance multifunction platform provides a single, cost-effective platform.The Cisco 7200 series delivers exceptional price/performance to meet the requirements of both enterprise and service providers. With its combination of scalable performance, density, and low per-port pricing, the Cisco 7200 allows network-layer capabilities to be extended to a much wider range of network configurations and environments. Customers can now gain the advantages of high-performance network-layer switching and services, including security, QoS, and traffic management to more locations throughout the network.

CISCO7206VXR data sheet
Product Description	Cisco 7206 VXR - modular expansion base
Manufacturer	Cisco Systems, Inc
Manufacturer Part Number	CISCO7206VXR
Product Type	Modular expansion base
Form Factor	External - modular
Dimensions (WxDxH)	42.7 cm x 43.2 cm x 13.3 cm
Features	Modular design
Power	AC 120/230 V ( 50/60 Hz )

The Cisco 7204VXR supports multiprotocol, multimedia routing and bridging with a wide variety of protocols and port adapter combinations available for Cisco 7200 series routers. In addition, the Cisco 7204VXR midplane provides increased support for multiple high-bandwidth port adapters. It has slots for port adapters, for an I/O controller, and for a network processing engine or network services engine. This device operates as either a tabletop or a rack-mounted unit. A rack-mount kit is a standard equipment included with all Cisco 7200 VXR routers when they are shipped from the factory.

CISCO7204VXR data sheet
Product Description	Cisco 7204 VXR - modular expansion base
Manufacturer	Cisco Systems, Inc
Manufacturer Part Number	CISCO7204VXR
Product Type	Modular expansion base
Form Factor	External - modular
Dimensions (WxDxH)	42.7 cm x 43.2 cm x 13.3 cm
Weight	22.7 kg
Features	Modular design
Power	AC 120/230 V ( 50/60 Hz )

Specifications
Type	Fixed
Topology	Ethernet (10/100/1000 Ethernet PortsBaseT) Gigabit Ethernet (SFP)
Maximum Port density	24 10/100/1000 Ethernet Ports PoE ports
Uplinks	4 SFP ports
Modular/Expansion Slots	n/a
Architecture	Layer 2 Switching (basic connectivity), Layer 2 Switching (intelligent services), Layer 3 Switching, Voice Enabled
Form Factor	Fixed, Rack Mountable, Standalone/Clustering
Dimensions	1.73 x 17.5 x 14.9 in.
DRAM	128 MB
Features
Specialized Service Modules	n/a
Security
DHCP Snooping
Dynamic ARP Inspection
IP Source Guard
RP Rate Limiters
TCP Intercept
802.1x
Port Security
Dynamic VLANs
Private VLANs
Private VLAN Edge
Secure Shell
SNMPv3
Unicast RPF
ACLs (L2-L4)
Kerberos
TACACS+
RADIUS
High Availability/Resilliency
Hardware Redundancy	External Redundant Power Supply
High Availability/Resilliency	PVST, Broadcast Suppression, Unicast Suppression, Mulitcast Suppression, Spanning Tree, Portfast, Uplink Fast, Backbone Fast, 802.1s, 802.1w, HSRP
Management
Management features	SPAN, RSPAN, CiscoView, Cisco Discover Protocol (CDP), Virtual Trunking Protocol (VTP), Telnet Client, BOOTP, TFTP, CiscoWorks, CWSI, RMON, SNMP, Clustering, Web-Based Management
Scalability
WAN Interface Support	n/a
Throughput	38.7 Mpps
Backplane Capacity	32 Gbps
Number of VLANs	4k, 1024
QOS/VoiceMulticast/Multimedia
Voice Services
IPv6 Support
WRR
QoS - Policing
QoS - Scheduling
802.1p
802.1Q
ISL
CGMP
DSCP
L2 -L4 QOS ACLs
PIM
DMRP
IGMP
IGMP Snooping
QOS - Multiqueues
QOS - Marking Classification
QPM
Power over Ethernet
Multilayer QOS/Security
Layer 2
Layer 3
Layer 4
Layer 4+

Cisco Catalyst 2960-S and 2960 Series Switches with LAN Lite Switch Configurations

Table 1. Configurations of Cisco Catalyst 2960-S and 2960 Series Switches with LAN Lite Software

Firewall ASA5505-50-BUN-K9
Firewall Users	50
Maximum firewall throughput (Mbps)	150
Maximum connections	25,000
Maximum connections/second	3,000
Packets per second (64 byte)	85,000
Application-layer security	Yes
Layer 2 transparent firewalling	Yes
Security contexts (included/maximum)3	0/0
GTP/GPRS inspection3	Not available
VPN
Maximum 3DES/AES VPN throughput (Mbps)	100
Maximum site-to-site and remote access IPsec VPN user sessions	25
SSL user session license included	2
Maximum SSL VPN user sessions1	25
VPN clustering and load balancing	Not available
UTM Features Included
Intrusion Prevention Included (Performance)	No
Content Security [anti-virus, anti-spyware, file blocking, anti-spam, anti-phishing, and URL filtering] (Max users)	No
Other Features
Integrated ports2	8 port 10/100 switch with 2 Power over Ethernet ports
Maximum virtual interfaces (VLANs)	20 (trunking enabled)
High availability support4	Stateless A/S

Firewall ASA5505-UL-BUN-K9
Firewall Users	Unlimited
Maximum firewall throughput (Mbps)	150
Maximum connections	25,000
Maximum connections/second	3,000
Packets per second (64 byte)	85,000
Application-layer security	Yes
Layer 2 transparent firewalling	Yes
Security contexts (included/maximum)3	0/0
GTP/GPRS inspection3	Not available
VPN
Maximum 3DES/AES VPN throughput (Mbps)	100
Maximum site-to-site and remote access IPsec VPN user sessions	25
SSL user session license included	2
Maximum SSL VPN user sessions1	25
VPN clustering and load balancing	Not available
UTM Features Included
Intrusion Prevention Included (Performance)	No
Content Security [anti-virus, anti-spyware, file blocking, anti-spam, anti-phishing, and URL filtering] (Max users)	No
Other Features
Integrated ports2	8 port 10/100 switch with 2 Power over Ethernet ports
Maximum virtual interfaces (VLANs)	20 (trunking enabled)
High availability support4	Stateless A/S

Firewall ASA5505-BUN-K9
Firewall Users	10
Maximum firewall throughput (Mbps)	150
Maximum connections	10,000
Maximum connections/second	3,000
Packets per second (64 byte)	85,000
Application-layer security	Yes
Layer 2 transparent firewalling	Yes
Security contexts (included/maximum)3	0/0
GTP/GPRS inspection3	Not available
VPN
Maximum 3DES/AES VPN throughput (Mbps)	100
Maximum site-to-site and remote access IPsec VPN user sessions	10
SSL user session license included	2
Maximum SSL VPN user sessions1	25
VPN clustering and load balancing	Not available
UTM Features Included
Intrusion Prevention Included (Performance)	No
Content Security [anti-virus, anti-spyware, file blocking, anti-spam, anti-phishing, and URL filtering] (Max users)	No
Other Features
Integrated ports2	8 port 10/100 switch with 2 Power over Ethernet ports
Maximum virtual interfaces (VLANs)	3 (trunking disabled)
High availability support4	Not supported

Firewall ASA5505-BUN-K9
Firewall Users	10
Maximum firewall throughput (Mbps)	150
Maximum connections	10,000
Maximum connections/second	3,000
Packets per second (64 byte)	85,000
Application-layer security	Yes
Layer 2 transparent firewalling	Yes
Security contexts (included/maximum)3	0/0
GTP/GPRS inspection3	Not available
VPN
Maximum 3DES/AES VPN throughput (Mbps)	100
Maximum site-to-site and remote access IPsec VPN user sessions	10
SSL user session license included	2
Maximum SSL VPN user sessions1	25
VPN clustering and load balancing	Not available
UTM Features Included
Intrusion Prevention Included (Performance)	No
Content Security [anti-virus, anti-spyware, file blocking, anti-spam, anti-phishing, and URL filtering] (Max users)	No
Other Features
Integrated ports2	8 port 10/100 switch with 2 Power over Ethernet ports
Maximum virtual interfaces (VLANs)	3 (trunking disabled)
High availability support4	Not supported

Firewall ASA5505-BUN-K9
Firewall Users	10
Maximum firewall throughput (Mbps)	150
Maximum connections	10,000
Maximum connections/second	3,000
Packets per second (64 byte)	85,000
Application-layer security	Yes
Layer 2 transparent firewalling	Yes
Security contexts (included/maximum)3	0/0
GTP/GPRS inspection3	Not available
VPN
Maximum 3DES/AES VPN throughput (Mbps)	100
Maximum site-to-site and remote access IPsec VPN user sessions	10
SSL user session license included	2
Maximum SSL VPN user sessions1	25
VPN clustering and load balancing	Not available
UTM Features Included
Intrusion Prevention Included (Performance)	No
Content Security [anti-virus, anti-spyware, file blocking, anti-spam, anti-phishing, and URL filtering] (Max users)	No
Other Features
Integrated ports2	8 port 10/100 switch with 2 Power over Ethernet ports
Maximum virtual interfaces (VLANs)	3 (trunking disabled)
High availability support4	Not supported

The platforms are architected to enable the next phase of branch-office evolution, providing rich media collaboration and virtualization to the branch while maximizing operational cost savings The integrated services routers generation 2 platforms are future-enabled with multi-core CPUs, support for high capacity DSPs (Digital Signal Processors) for future enhanced video capabilities, high powered service modules with improved availability, Gigabit Ethernet switching with enhanced POE, and energy monitoring and control capabilities while enhancing overall system performance. Overall, the Cisco 2900 series offer unparalleled total cost of ownership savings and network agility through the intelligent integration of market leading security, unified communications, wireless, and application services.The Cisco 2900 series integrated services router offers embedded hardware encryption acceleration, voice- and video-capable Digital Signal Processor (DSP) slots, intrusion prevention, call processing, voicemail, and application services.

CISCO2911-SEC/K9 data sheet
Manufacturer	Cisco Systems, Inc
Manufacturer Part Number	CISCO2911-SEC/K9
Product Type	Router
Form Factor	External - modular - 2U
Dimensions (WxDxH)	43.8 cm x 30.5 cm x 8.9 cm
Weight	8.2 kg
DRAM Memory	512 MB (installed) / 2 GB (max)
Flash Memory	256 MB (installed) / 8 GB (max)
Routing Protocol	OSPF, IS-IS, BGP, EIGRP, DVMRP, PIM-SM, IGMPv3, GRE, PIM-SSM, static IPv4 routing, static IPv6 routing
Data Link Protocol	Ethernet, Fast Ethernet, Gigabit Ethernet
Network / Transport Protocol	IPSec
Remote Management Protocol	SNMP, RMON
Features	Firewall protection, hardware encryption, VPN support, MPLS support, Syslog support, content filtering, IPv6 support, Class-Based Weighted Fair Queuing (CBWFQ), Weighted Random Early Detection (WRED), Dynamic Multipoint VPN (DMVPN)
Compliant Standards	IEEE 802.1Q, IEEE 802.3af, IEEE 802.3ah, IEEE 802.1ah, IEEE 802.1ag
Power	AC 120/230 V ( 50/60 Hz )
Manufacturer Warranty	90 days warranty

The award-winning Cisco 3800 Series integrated services routers, ideal for medium-sized to large businesses and enterprise branch offices, enable you to simplify deployment and management, lower the costs and complexities of your network, and support mission-critical business applications, by providing a highly secure platform with concurrent T3/E3 wire-speed delivery.Cisco 3800 Series routers deliver the performance, availability, and reliability required for scaling mission-critical business applications in the most demanding enterprise environments.

CISCO3845 data sheet
Manufacturer	Cisco Systems, Inc
Manufacturer Part Number	CISCO3845
Product Type	Router
Form Factor	External - modular - 3U
Dimensions (WxDxH)	43.8 cm x 40.6 cm x 13.3 cm
Weight	15.9 kg
DRAM Memory	512 MB (installed) / 1 GB (max) - DDR SDRAM
Flash Memory	128 MB (installed) / 512 MB (max)
Data Link Protocol	Ethernet, Fast Ethernet, Gigabit Ethernet
Network / Transport Protocol	IPSec
Remote Management Protocol	SNMP 3, HTTP, SSH-2
Features	Cisco IOS IP Base , firewall protection, hardware encryption, VPN support, MPLS support, URL filtering
Power	AC 120/230 V ( 50/60 Hz )

The award-winning Cisco 3800 Series integrated services routers, ideal for medium-sized to large businesses and enterprise branch offices, enable you to simplify deployment and management, lower the costs and complexities of your network, and support mission-critical business applications, by providing a highly secure platform with concurrent T3/E3 wire-speed delivery.Cisco 3800 Series routers deliver the performance, availability, and reliability required for scaling mission-critical business applications in the most demanding enterprise environments.

CISCO3845 data sheet
Manufacturer	Cisco Systems, Inc
Manufacturer Part Number	CISCO3845
Product Type	Router
Form Factor	External - modular - 3U
Dimensions (WxDxH)	43.8 cm x 40.6 cm x 13.3 cm
Weight	15.9 kg
DRAM Memory	512 MB (installed) / 1 GB (max) - DDR SDRAM
Flash Memory	128 MB (installed) / 512 MB (max)
Data Link Protocol	Ethernet, Fast Ethernet, Gigabit Ethernet
Network / Transport Protocol	IPSec
Remote Management Protocol	SNMP 3, HTTP, SSH-2
Features	Cisco IOS IP Base , firewall protection, hardware encryption, VPN support, MPLS support, URL filtering
Power	AC 120/230 V ( 50/60 Hz )

WS-C2960S-24TS-L Specifications
General Information
Manufacturer	Cisco
Product ID:	WS-C2960S-24TS-L
Product Description:	Cisco CAT2960S Stack 24 Gige-4 x SFP LAN Base
Product Type:	Ethernet Switch
Marketing Information
The Cisco Catalyst 2960-S and 2960 Series Switches with LAN Base provide the performance, and availability that today's small businesses demand, as well as the intelligence to support business applications and security services. Switches are a key component of your network foundation and can improve the availability of critical applications, while protecting business information. The Cisco Catalyst 2960-S and 2960 Series Switches are specifically designed for growing businesses that need to accommodate expanding services, and optimize network bandwidth and to assure the fast and reliable delivery of applications and services.
Interfaces/Ports
Number of Ports:	24
Gigabit Ethernet Port:	Yes
Interfaces/Ports:	24 x RJ-45 10/100/1000Base-T Network LAN
Media & Performance
Forwarding/Filtering Rate:	41.7 Mpps
Switching Throughput:	176 Gbps
I/O Expansions
Number of Expansion Slots:	5
Expansion Slots:	(4 Total) SFP (mini-GBIC) Uplink
	(1 Total) Stacking Module
Network & Communication
Layer Support:	2
Management & Protocols
Manageable:	Yes
Management:	DHCP QoS VLAN SNMP v1, v2, v3 Syslog CLI RMON CiscoWorks LAN Management Solution
Memory
Standard Memory:	128MB
Memory Technology:	DRAM
Flash Memory:	64MB
Software
Operating System:	Cisco IOS
Power Description
Input Voltage:	110 V AC
	220 V AC
Input Voltage Range:	100 V AC to 240 V AC
Power Source:	Power Supply
Redundant Power Supply:	Yes
Physical Characteristics
Compatible Rack Unit:	1U
Form Factor:	Rack-mountable
	Stackable
Dimensions:	1.75" Height x 17.50" Width x 11.80" Depth
Weight (Approximate):	10 lb

The industry-standard Cisco Small Form-Factor Pluggable (SFP) Gigabit Interface Converter is a hot-swappable input/output device that plugs into a Gigabit Ethernet port or slot, linking the port with the network (Figures 1, 2 and 3). SFPs can be used and interchanged on a wide variety of Cisco products and can be intermixed in combinations of 1000BASE-T, 1000BASE-SX, 1000BASE-LX/LH, 1000BASE-EX, 1000BASE-ZX, or 1000BASE-BX10-D/U on a port-by-port basis.
SFP Port Cabling Specifications

Specifications
Type	Fixed
Topology	Ethernet (10/100BaseTX) Ethernet (10/100/1000BaseT) Gigabit Ethernet (SFP)
Maximum Port density	24 10/100 ports
Uplinks	2 dual-purpose (10/100/1000 or SFP) ports
Modular/Expansion Slots	n/a
Architecture	Layer 2 Switching (basic connectivity), Layer 2 Switching (intelligent services), Voice Enabled
Form Factor	Fixed, Rack Mountable, Standalone/Clustering
Dimensions	1.73 x 17.5 x 9.3 in.
DRAM	64 MB
Features
Specialized Service Modules	n/a
Security
DHCP Snooping
Dynamic ARP Inspection
IP Source Guard
RP Rate Limiters
TCP Intercept
802.1x
Port Security
Dynamic VLANs
Private VLANs
Private VLAN Edge
Secure Shell
SNMPv3
Unicast RPF
ACLs (L2-L4)
Kerberos
TACACS+
RADIUS
High Availability/Resilliency
Hardware Redundancy	External Redundant Power Supply
High Availability/Resilliency	PVST, Broadcast Suppression, Unicast Suppression, Mulitcast Suppression, Spanning Tree, Portfast, Uplink Fast, Backbone Fast, 802.1s, 802.1w
Management
Management features	SPAN, RSPAN, CiscoView, Cisco Discover Protocol (CDP), Virtual Trunking Protocol (VTP), Telnet Client, BOOTP, TFTP, CiscoWorks, CWSI, RMON, SNMP, Clustering, Web-Based Management
Scalability
WAN Interface Support	n/a
Throughput	6.5 Mpps
Backplane Capacity	16 Gbps
Number of VLANs	255

Specifications
Type	Fixed
Topology	Ethernet (10/100BaseTX) Ethernet (10/100/1000BaseT) Gigabit Ethernet (SFP)
Maximum Port density	24 10/100 ports
Uplinks	2 dual-purpose (10/100/1000 or SFP) ports
Modular/Expansion Slots	n/a
Architecture	Layer 2 Switching (basic connectivity), Layer 2 Switching (intelligent services), Voice Enabled
Form Factor	Fixed, Rack Mountable, Standalone/Clustering
Dimensions	1.73 x 17.5 x 9.3 in.
DRAM	64 MB
Features
Specialized Service Modules	n/a
Security
DHCP Snooping
Dynamic ARP Inspection
IP Source Guard
RP Rate Limiters
TCP Intercept
802.1x
Port Security
Dynamic VLANs
Private VLANs
Private VLAN Edge
Secure Shell
SNMPv3
Unicast RPF
ACLs (L2-L4)
Kerberos
TACACS+
RADIUS
High Availability/Resilliency
Hardware Redundancy	External Redundant Power Supply
High Availability/Resilliency	PVST, Broadcast Suppression, Unicast Suppression, Mulitcast Suppression, Spanning Tree, Portfast, Uplink Fast, Backbone Fast, 802.1s, 802.1w
Management
Management features	SPAN, RSPAN, CiscoView, Cisco Discover Protocol (CDP), Virtual Trunking Protocol (VTP), Telnet Client, BOOTP, TFTP, CiscoWorks, CWSI, RMON, SNMP, Clustering, Web-Based Management
Scalability
WAN Interface Support	n/a
Throughput	6.5 Mpps
Backplane Capacity	16 Gbps
Number of VLANs	255

Cisco 2900 series offer unparalleled total cost of ownership savings and network agility through the intelligent integration of market leading security, unified communications, wireless, and application services.The Cisco 2900 series ISRs offer embedded hardware encryption acceleration, voice- and video-capable digital signal processor (DSP) slots, optional firewall, intrusion prevention, call processing, voicemail, and application services. In addition, the platforms support the industries widest range of wired and wireless connectivity options such as T1/E1, xDSL, copper and fiber GE.

Cisco 2901 Router Details
Product Description	Cisco 2901 Integrated Services Router - router
Manufacturer	Cisco Systems, Inc
Manufacturer Part Number	CISCO2901/K9
Product Type	Router
Form Factor	External - modular - 1U
Dimensions (WxDxH)	43.9 cm x 43.8 cm x 4.5 cm
Weight	6.1 kg
DRAM Memory	512 MB (installed) / 2 GB (max)
Flash Memory	256 MB (installed) / 8 GB (max)
Routing Protocol	OSPF, IS-IS, BGP, EIGRP, DVMRP, PIM-SM, IGMPv3, GRE, PIM-SSM, static IPv4 routing, static IPv6 routing
Data Link Protocol	Ethernet, Fast Ethernet, Gigabit Ethernet
Remote Management Protocol	SNMP, RMON
Features	Cisco IOS IP Base , MPLS support, Syslog support, IPv6 support, Class-Based Weighted Fair Queuing (CBWFQ), Weighted Random Early Detection (WRED)
Compliant Standards	IEEE 802.1Q, IEEE 802.3af, IEEE 802.3ah, IEEE 802.1ah, IEEE 802.1ag
Power	AC 120/230 V ( 50/60 Hz )

Cisco 2900 series offer unparalleled total cost of ownership savings and network agility through the intelligent integration of market leading security, unified communications, wireless, and application services.The Cisco 2900 series ISRs offer embedded hardware encryption acceleration, voice- and video-capable digital signal processor (DSP) slots, optional firewall, intrusion prevention, call processing, voicemail, and application services. In addition, the platforms support the industries widest range of wired and wireless connectivity options such as T1/E1, xDSL, copper and fiber GE.

Cisco 2901 Router Details
Product Description	Cisco 2901 Integrated Services Router - router
Manufacturer	Cisco Systems, Inc
Manufacturer Part Number	CISCO2901/K9
Product Type	Router
Form Factor	External - modular - 1U
Dimensions (WxDxH)	43.9 cm x 43.8 cm x 4.5 cm
Weight	6.1 kg
DRAM Memory	512 MB (installed) / 2 GB (max)
Flash Memory	256 MB (installed) / 8 GB (max)
Routing Protocol	OSPF, IS-IS, BGP, EIGRP, DVMRP, PIM-SM, IGMPv3, GRE, PIM-SSM, static IPv4 routing, static IPv6 routing
Data Link Protocol	Ethernet, Fast Ethernet, Gigabit Ethernet
Remote Management Protocol	SNMP, RMON
Features	Cisco IOS IP Base , MPLS support, Syslog support, IPv6 support, Class-Based Weighted Fair Queuing (CBWFQ), Weighted Random Early Detection (WRED)
Compliant Standards	IEEE 802.1Q, IEEE 802.3af, IEEE 802.3ah, IEEE 802.1ah, IEEE 802.1ag
Power	AC 120/230 V ( 50/60 Hz )

Cisco 2900 series offer unparalleled total cost of ownership savings and network agility through the intelligent integration of market leading security, unified communications, wireless, and application services.The Cisco 2900 series ISRs offer embedded hardware encryption acceleration, voice- and video-capable digital signal processor (DSP) slots, optional firewall, intrusion prevention, call processing, voicemail, and application services. In addition, the platforms support the industries widest range of wired and wireless connectivity options such as T1/E1, xDSL, copper and fiber GE.

Cisco 2901 Router Details
Product Description	Cisco 2901 Integrated Services Router - router
Manufacturer	Cisco Systems, Inc
Manufacturer Part Number	CISCO2901/K9
Product Type	Router
Form Factor	External - modular - 1U
Dimensions (WxDxH)	43.9 cm x 43.8 cm x 4.5 cm
Weight	6.1 kg
DRAM Memory	512 MB (installed) / 2 GB (max)
Flash Memory	256 MB (installed) / 8 GB (max)
Routing Protocol	OSPF, IS-IS, BGP, EIGRP, DVMRP, PIM-SM, IGMPv3, GRE, PIM-SSM, static IPv4 routing, static IPv6 routing
Data Link Protocol	Ethernet, Fast Ethernet, Gigabit Ethernet
Remote Management Protocol	SNMP, RMON
Features	Cisco IOS IP Base , MPLS support, Syslog support, IPv6 support, Class-Based Weighted Fair Queuing (CBWFQ), Weighted Random Early Detection (WRED)
Compliant Standards	IEEE 802.1Q, IEEE 802.3af, IEEE 802.3ah, IEEE 802.1ah, IEEE 802.1ag
Power	AC 120/230 V ( 50/60 Hz )

VWIC3-2MFT-T1/E1
Manufacturer	Cisco
Part Number	VWIC3-2MFT-T1/E1
Device Type	Interface module
Form factor	2-Port T1/E1 Multiflex Trunk Voice/WAN Interface Card
Specifications
Number of Ports	2
T1 Support	Yes
E1 Support	Yes
Unstructured E1 (G.703) Support	No
Data Support WIC Mode	Yes
Voice Support VIC*	Yes
Drop-and-Insert Multiplexing	Yes
Configuration Comparison
Serial Data (channel-group*)	2 total 2 per port
Voice CAS (ds0-group**)	48 total (T1) 62 total (E1) 1 per timeslot
PRI (pri-group***)	2 total 1 per port
Drop & Insert (tdm-group****)	48 total (T1) 62 total (E1) 1 per timeslot
Network Management Features
Telnet or Console	Remote and local configuration, monitoring, and troubleshooting from Cisco IOS Software CLI
Simple Network Management Protocol (SNMP)	• Router and DSU/CSU managed by single SNMP agent; router, DSU, and CSU appear as a single network entity to user • Standard MIB (MIB II) • Cisco Integrated DSU/CSU MIB • RFC 1406 T1 MIB, Including Alarm Detection and Reporting
SNMP Traps	Generated in response to alarms

VWIC3-1MFT-T1/E1
Manufacturer	Cisco
Part Number	VWIC3-1MFT-T1/E1
Device Type	Interface module
Form factor	1-Port T1/E1 Multiflex Trunk Voice/WAN Interface Card
Specifications
Number of Ports	1
T1 Support	Yes
E1 Support	Yes
Unstructured E1 (G.703) Support	No
Data Support WIC Mode	Yes
Voice Support VIC*	Yes
Drop-and-Insert Multiplexing	Yes
Configuration Comparison
Serial Data (channel-group*)	2 total 2 per port
Voice CAS (ds0-group**)	24 total (T1) 31 total (E1) 1 per timeslot
PRI (pri-group***)	1 total 1 per port
Drop & Insert (tdm-group****)	24 total (T1) 31 total (E1) 1 per timeslot
Network Management Features
Telnet or Console	Remote and local configuration, monitoring, and troubleshooting from Cisco IOS Software CLI
Simple Network Management Protocol (SNMP)	• Router and DSU/CSU managed by single SNMP agent; router, DSU, and CSU appear as a single network entity to user • Standard MIB (MIB II) • Cisco Integrated DSU/CSU MIB • RFC 1406 T1 MIB, Including Alarm Detection and Reporting
SNMP Traps	Generated in response to alarms

General Information
Manufacturer:	Cisco
Product ID:	VIC-4FXS/DID
Product Description:	4 port FXS or DID VIC
Product Type:	Voice Interface Card (VIC)
Marketing Information
The 4-port high-density FXS/DID VIC can support up to 4 foreign-exchange-station (FXS) ports for directly connecting phones or fax machines, or it can be used to connect up to four direct-inward-dial (DID) analog trunks, providing customers the flexibility they need for their unique business environment. Each port on the 4-Port FXS/DID VIC is selectable for use in either FXS or DID mode. The 4-Port FXS/DID VIC is the same size as the existing two-port voice interface cards (VICs), allowing it to slide into either WIC/VIC slot or VIC slot in Cisco 1751 and 1760. The VIC-4FXS/DID in the Cisco 1700 is used to connect analog phones or fax machines. The long-distance calls between small enterprise branch offices and headquarters are carried by IP network, while the local calls are carried by PSTN, which also provide backup to the IP network.
Technical Information
Application/Usage:	Voice
Interfaces/Ports
Interfaces/Ports:	4 x FXS/DID
Interfaces/Ports Details:	4 x RJ-11 FXS/DID
Reliability
MTBF:	2131306 Hour
Miscellaneous
Additional Information:	For Cisco 2600XM, 2691, 3640, 3660, and 3700 platforms, only FXS functionality is supported For the VIC-4FXS/DID, the Cisco 1751 and 1760 platforms are the only places where both the DID functionality and FXS functionality of the card are supported Voice & Fax Integration Caller ID support A maximum of eight REN loads can be supported on each 4-port FXS/DID VIC Minimum Feature Sets: IP/VOX PLUS Ringing frequencies: 20 Hz, 50 Hz Tone disconnect supervision: DID-Power denial (caller party control, far-end disconnect) Signaling Formats: DID mode: Immediate, delay dial, wink start FXS mode: Groundstart and loopstart Address Signaling formats: In-band dual tone multifrequency (DTMF) Out-of-band pulse (10/20 pps)
System Requirements:	Supported Platforms & Minimum IOS Versions: 3845 - 12.3(11)T 3825 - 12.3(11)T 3745 - 12.2(15)ZJ 3725 - 12.2(15)ZJ 3660 series - 12.2(15)ZJ 2691 - 12.2(15)ZJ 2600XM Series - 12.2(15)ZJ 1760 - 12.2(8)YN 1751 - 12.2(15)ZL
Compatibility:	Supported Platforms: 3845 3825 3745 3725 3640 3660 series 2691 2600XM Series 1760 1751 Supported Carrier Modules: 2600XM: NM-1V, NM-2V, NM-HD-1V, NM-HD-2V, NM-HD-2VE, NM-HDV2-1T1/E1, NM-HDV2-2T1/E1 3640, 3660: NM-1V, NM-2V, NM-HD-1V, NM-HD-2V, NM-HD-2VE 2691, 3725, 3745: NM-1V, NM-2V, NM-HD-1V, NM-HD-2V, NM-HD-2VE, NM-HDV2, NM-HDV2-1T1/E1, NM-HDV2-2T1/E1
Certifications & Standards:	Compliance: FCC Class B device CE Safety Conformance: UL1950

General Information
Manufacturer:	Cisco
Product ID:	VIC2-4FXO
Product Description:	Four-port Voice Interface Card - FXO (Universal)
Product Type:	Voice Interface Card (VIC)
Marketing Information
This VIC include 4-port foreign exchange station (FXS). This card cover a full range of digital voice and WAN connectivity options and provide connectivity to the world's PBXs, PSTNs, and Post, Telephone, and Telegraph (PTT) organizations.
Technical Information
Application/Usage:	Voice
Interfaces/Ports
Interfaces/Ports:	4 x FXO WAN
Interfaces/Ports Details:	4 x RJ-11 FXO WAN
Miscellaneous
Additional Information:	Loop Start Support Voice & Fax Integration Supports CAMA with software configuration This Module Support Ground Start This Module Support Battery Reversal This Module Support Caller ID
System Requirements:	Supported Platforms & Minimum IOS Versions: 3745 - 12.2(15)ZJ 3725 - 12.2(15)ZJ 3660 series - 12.2(15)ZJ 2691 - 12.2(15)ZJ 2600XM Series - 12.2(15)ZJ 1760 - 12.2(15)ZL 1751 - 12.2(15)ZL
Compatibility:	NM-HD-1V Network Module NM-HD-2V Network Module NM-HD-2VE Network Module Supported Platforms: 3745 3725 3660 series 2691 2600XM series 1760 1751

General Information
Manufacturer:	Cisco
Product ID:	VIC2-2E/M
Product Description:	Two-port Voice Interface Card - EandM
Product Type:	Voice Interface Card (VIC)
Marketing Information
An Ear and Mouth (E&M) interface is used to support tie-line facilities or signals between telephone switches. The E&M voice interface card (VIC) is mostly used to integrate VoIP with the legacy voice solution, connecting the Cisco router to a PBX.
Technical Information
Application/Usage:	Voice
Interfaces/Ports
Interfaces/Ports:	2 x E&M WAN
Interfaces/Ports Details:	2 x RJ-45 E&M WAN
Management & Protocols
Protocols:	MGCP
Reliability
MTBF:	1825192 Hour
Environmental Conditions
Temperature:	32?F (0?C) to 104?F (40?C) Operating
	-13?F (-25?C) to 158?F (70?C) Storage
Humidity:	5% to 85% Non-condensing Relative Humidity Operating
	5% to 95% Non-condensing Relative Humidity Non-operating
Miscellaneous
Additional Information:	Use Cisco CallManager version 3.3(3) for MGCP support E-Lead Current Limit: 100 mA M-Lead Sensitivity: > 3 mA Pulse Distortion: < 2 percent "Plus" feature set support Connections: Supports two-wire and four-wire E&M signaling types I, II, III, and V via RJ-45/RJ-48S connectors Signaling Modes: Immediate Delay dial Wink start Address Signaling Formats: In-band DTMF Out-of-band pulse (10/20 pps)
System Requirements:	Supported Platforms & Minimum IOS Versions: 3745 - 12.2(15)ZJ 3725 - 12.2(15)ZJ 3660 Series - 12.2(15)ZJ 2691 - 12.2(15)ZJ 2600XM Series - 12.2(15)ZJ 1760 - 12.2(15)ZL 1751 - 12.2(15)ZL
Compatibility:	NM-HD-1V Network Module NM-HD-2V Network Module NM-HD-2VE Network Module Supported Platforms: 3745 3725 3660 Series 2691 2600XM Series 1760 1751
Certifications & Standards:	Compliance: FCC Class B device CE Safety Conformance: UL 1950

General Information
Manufacturer:	Cisco
Product ID:	VIC2-2FXS
Product Description:	Two-port Voice Interface Card - FXS
Product Type:	Voice Interface Card (VIC)
Marketing Information
This VIC include 2-port foreign exchange station (FXS). A Foreign Exchange Station (FXS) interface connects directly to a standard telephone, fax machine, or similar device and supplies ring, voltage, and dial tone. The Cisco FXS interface is an RJ-11 connector that allows connections to basic telephone service equipment, keysets, and PBXes.
Technical Information
Application/Usage:	Voice
Interfaces/Ports
Interfaces/Ports:	2 x FXS WAN
Interfaces/Ports Details:	2 x RJ-11 FXS WAN
Miscellaneous
Additional Information:	Voice & Fax Integration Connects to a telephone or fax, or to a PBX or key set that emulates a telephone Cisco IOS Software "Plus" Feature Set Support
System Requirements:	Supported Platforms & Minimum IOS Versions: 3745 - 12.2(15)ZJ 3725 - 12.2(15)ZJ 3660 series - 12.2(15)ZJ 2691 - 12.2(15)ZJ 2600XM Series - 12.2(15)ZJ 1760 - 12.2(15)ZL 1751 - 12.2(15)ZL
Compatibility:	NM-HD-1V Network Module NM-HD-2V Network Module NM-HD-2VE Network Module Supported Platforms: 3745 3725 3660 series 2691 2600XM series 1760 1751

General Information
Manufacturer:	Cisco
Product ID:	VIC2-2FXO
Product Description:	Two-port Voice Interface Card - FXO (Universal)
Product Type:	Voice Interface Card (VIC)
Marketing Information
(VIC2-2FXO=) include 2-port foreign exchange office (FXO) analog interface cards. This card cover a full range of digital voice and WAN connectivity options and provide connectivity to the world's PBXs, PSTNs, and Post, Telephone, and Telegraph (PTT) organizations.
Technical Information
Application/Usage:	Voice
Interfaces/Ports
Interfaces/Ports:	2 x FXO WAN
Interfaces/Ports Details:	2 x RJ-11 FXO WAN
Miscellaneous
Additional Information:	Supports Centralized Automatic Message Accounting (CAMA) with software configuration Loop Start Supported Voice and Fax Integration
System Requirements:	Supported Platforms & Minimum IOS Versions: 3745 - 12.2(15)ZJ 3725 - 12.2(15)ZJ 3660 Series - 12.2(15)ZJ 3640 - 12.2(15)ZJ 3620 - Not Supported 2691 - 12.2(15)ZJ 2600XM Series - 12.2(15)ZJ 2600 Series - Not Supported 1760 - 12.2(15)ZL 1751 - 12.2(15)ZL Requires Battery Reversal Requires Caller ID
Compatibility:	Supported Platforms: 3745 3725 3660 Series 3640 3620 2691 2600XM Series 2600 Series 1760 1751 Software Compatibility: 1751 - 12.3(4)T, 12.3(4)XG, 12.3(5) 1760 - 12.3(4)T, 12.3(4)XG, 12.3(5) 2600XM - 12.3(4)T, 12.3(7)T 3640 - 12.3(4)T 3660 - 12.3(4)T 2691 - 12.3(4)T, 12.3(7)T IAD2431 - 12.3(4)XD, 12.3(7)T IAD2432 - 12.3(4)XD, 12.3(7)T 3725 - 12.3(4)T, 12.3(7)T 3745 - 12.3(4)T, 12.3(7)T This card works in NM-HD-1V, NM-HD-2V, and NM-HD-2VE

VWIC3-2MFT-G703
Manufacturer	Cisco
Part Number	VWIC3-2MFT-G703
Device Type	Interface module
Form factor	2-Port G.703 Multiflex Trunk Voice/WAN Interface Card
Specifications
Number of Ports	2
T1 Support	Yes
E1 Support	Yes
Unstructured E1 (G.703) Support	Yes
Data Support WIC Mode	Yes
Voice Support VIC*	Yes
Drop-and-Insert Multiplexing	Yes
Configuration Comparison
Serial Data (channel-group*)	2 total 2 per port
Voice CAS (ds0-group**)	48 total (T1) 62 total (E1) 1 per timeslot
PRI (pri-group***)	2 total 1 per port
Drop & Insert (tdm-group****)	48 total (T1) 62 total (E1) 1 per timeslot
Network Management Features
Telnet or Console	Remote and local configuration, monitoring, and troubleshooting from Cisco IOS Software CLI
Simple Network Management Protocol (SNMP)	• Router and DSU/CSU managed by single SNMP agent; router, DSU, and CSU appear as a single network entity to user • Standard MIB (MIB II) • Cisco Integrated DSU/CSU MIB • RFC 1406 T1 MIB, Including Alarm Detection and Reporting
SNMP Traps	Generated in response to alarms

VWIC3-1MFT-G703
Manufacturer	Cisco
Part Number	VWIC3-1MFT-G703
Device Type	Interface module
Form factor	1-Port G.703 Multiflex Trunk Voice/WAN Interface Card
Specifications
Number of Ports	1
T1 Support	Yes
E1 Support	Yes
Unstructured E1 (G.703) Support	Yes
Data Support WIC Mode	Yes
Voice Support VIC*	Yes
Drop-and-Insert Multiplexing	Yes
Configuration Comparison
Serial Data (channel-group*)	2 total 2 per port
Voice CAS (ds0-group**)	24 total (T1) 31 total (E1) 1 per timeslot
PRI (pri-group***)	1 total 1 per port
Drop & Insert (tdm-group****)	24 total (T1) 31 total (E1) 1 per timeslot
Network Management Features
Telnet or Console	Remote and local configuration, monitoring, and troubleshooting from Cisco IOS Software CLI
Simple Network Management Protocol (SNMP)	• Router and DSU/CSU managed by single SNMP agent; router, DSU, and CSU appear as a single network entity to user • Standard MIB (MIB II) • Cisco Integrated DSU/CSU MIB • RFC 1406 T1 MIB, Including Alarm Detection and Reporting
SNMP Traps	Generated in response to alarms

General Information
Manufacturer:	Cisco
Product ID:	VWIC2-1MFT-G703
Product Description:	1-Port 2nd Gen Multiflex Trunk Voice/WAN Int. Card - G.703
Product Type:	Voice/WAN Interface Card
Marketing Information
The Cisco 1-port G.703 (E1) Voice/Wan Interface Card provide voice and data access to the public switched telephone network (PSTN). This multiflex trunk interface card is single-port trunk interfaces for voice, data, and integrated voice and/or data applications. This E1 multiflex VWIC with G.703 support allow unstructured E1 traffic that conforms to the ITU-T G.703 standard.
Technical Information
Application/Usage:	Voice
Interfaces/Ports
Interfaces/Ports:	1 x E1 WAN
Interfaces/Ports Details:	1 x RJ-48 E1 WAN
Media & Performance
Data Transfer Rate:	2.05 Mbps E1
Management & Protocols
Management:	MIB and Simple Network Management Protocol (SNMP) management
Protocols:	SNMP
Environmental Conditions
Temperature:	32?F (0?C) to 104?F (40?C) Operating
	-13?F (-25?C) to 158?F (70?C) Storage
Humidity:	5% to 85% Non-condensing Relative Humidity Operating
	5% to 95% Non-condensing Relative Humidity Non-operating
Miscellaneous
Additional Information:	Although unstructured G.703 operation is particular to E1 operation, the VWIC2 card also support structured T1 operation Controller local loopbacks Controller remote loopbacks Integrated CSU/DSU MIB Firmware to support T1 and E1 Layer 1 homologation User-initiated VWIC reset and field-programmable gate array (FPGA) download Voice support (includes DS0-group and PRI-group configuration) MFT VWIC2 has an onboard slot for a multiflex trunk dedicated echo cancellation module Dedicated Echo Cancellation module is not supported on MFT VWIC2 when MFT VWIC2 is used on the Cisco 1751 or 1760
Compatibility:	Supported Router Platforms: 1721 1751 1760 1841 2610XM 2611XM 2620XM 2621XM 2650XM 2651XM 2691 2801 2811 2821 2851 Cisco 3800 series platforms Supported Network Module: NM-HDV2 NM-2W NM-1FE1R2W NM-1FE2W-V2 NM-2FE2W-V2
Certifications & Standards:	ITU-T G.703 RFC 1406

General Information
Manufacturer:	Cisco
Product ID:	VWIC2-1MFT-T1/E1
Product Description:	1-Port 2nd Gen Multiflex Trunk Voice/WAN Int. Card - T1/E1
Product Type:	Voice/WAN Interface Card
Marketing Information
The Cisco 1 port T1/E1 multiflex interface card support generic single-port T1 or E1 trunk interfaces for voice, data, and integrated voice and/or data applications. This card provide basic structured T1 service, as well as structured and unstructured E1 services.
Technical Information
Application/Usage:	Voice
Interfaces/Ports
Interfaces/Ports:	1 x T1/E1 WAN
Interfaces/Ports Details:	1 x RJ-48C T1/E1 WAN
Media & Performance
Data Transfer Rate:	1.54 Mbps T1 2.05 Mbps E1
Management & Protocols
Management:	MIB and Simple Network Management Protocol (SNMP)
Protocols:	SNMP
Controls/Indicators
Status Indicators:	AL, LP, CD
Miscellaneous
Additional Information:	The card include an integrated data service unit/channel service unit (DSU/CSU) Shielded cables STP Cat 5 should be used on E1 ports Full support for T1 Facility Data Link (FDL) Controller local loopbacks Controller remote loopbacks Firmware to support T1 and E1 Layer 1 homologation User-initiated VWIC reset and field-programmable gate array (FPGA) download Voice support (includes DS0-group and PRI-group configuration) Drop and insert capability MFT VWIC2s have an onboard slot for a multiflex trunk dedicated echo cancellation module (EC-MFT-32 and EC-MFT-64), offering an enhanced echo cancellation capability for demanding network conditions.
Compatibility:	Cisco 2600XM series, Cisco 2691, Cisco 2800 series, Cisco 3700 series, and Cisco 3800 series routers Cisco 1700 Series Modular Access Routers Supported Network Module: NM-HDV NM-HDV2 NM-HD-2VE NM-2W NM-1FE1R2W NM-1FE2W-V2 NM-2FE2W-V2
Certifications & Standards:	ITU-T G.164 ITU-T G.165 ITU-T G.168 RFC 1406 MIBs: RFC 1406 MIB T1 CSU MIB Support Port Module MIB T1/E1 Line Status Reporting

General Information
Manufacturer:	Cisco
Product ID:	VWIC2-2MFT-T1/E1
Product Description:	2-Port 2nd Gen Multiflex Trunk Voice/WAN Int. Card - T1/E1
Product Type:	Voice/WAN Interface Card
Marketing Information
The Cisco 2-port T1/E1 multiflex interface cards provide voice and data access to the PSTN domain through TDM ports. They are dual-port trunk interfaces for voice, data, and integrated voice and/or data applications. These cards provide basic structured service for T1 or E1 networks and unstructured service for fractional E1 networks. The cards include an integrated DSU/CSU. Some cards also support the drop-and-insert process, which adds data to a T1 or E1 data stream, or which terminates data from a T1 or E1 data stream to other devices connected to the drop-and-insert equipment.
Technical Information
Application/Usage:	Voice
Interfaces/Ports
Interfaces/Ports:	2 x T1/E1 WAN
Interfaces/Ports Details:	2 x RJ-48C T1/E1 WAN
Media & Performance
Connectivity Media:	Category 5 STP/UTP
Data Transfer Rate:	1.54 Mbps T1 2.05 Mbps E1
Management & Protocols
Management:	MIB and Simple Network Management Protocol (SNMP)
Protocols:	SNMP
Controls/Indicators
Status Indicators:	AL, LP, CD
Miscellaneous
Additional Information:	The card include an integrated data service unit/channel service unit (DSU/CSU) Shielded cables STP Cat 5 should be used on E1 ports Full support for T1 Facility Data Link (FDL) Controller local loopbacks Controller remote loopbacks Firmware to support T1 and E1 Layer 1 homologation User-initiated VWIC reset and field-programmable gate array (FPGA) download Voice support (includes DS0-group and PRI-group configuration) Drop and insert capability MFT VWIC2s have an onboard slot for a multiflex trunk dedicated echo cancellation module (EC-MFT-32 and EC-MFT-64), offering an enhanced echo cancellation capability for demanding network conditions.
Compatibility:	Cisco 2600XM series, Cisco 2691, Cisco 2800 series, Cisco 3700 series, and Cisco 3800 series routers Cisco 1700 Series Modular Access Routers Supported Network Module: NM-HDV NM-HDV2 NM-HD-2VE NM-2W NM-1FE1R2W NM-1FE2W-V2 NM-2FE2W-V2
Certifications & Standards:	ITU-T G.164 ITU-T G.165 ITU-T G.168 RFC 1406 MIBs: RFC 1406 MIB T1 CSU MIB Support Port Module MIB T1/E1 Line Status Reporting

General Information
Manufacturer:	Cisco
Product ID:	EHWIC-1GE-SFP-CU
Product Description:	NEW; LIMITED AVAILABILITY!! Cisco EHWIC 1 port dual mode SFP(100M/1G) or GE(10M/100M/1G)
Product Type:	HWIC
Marketing Information
The Cisco Gigabit Ethernet WAN EHWIC (EHWIC-1GE-SFP-CU) is an enhanced high-speed interface card providing copper and optical Gigabit Ethernet ports and connectivity of T1/E1 and T3/E3 over copper for Cisco ISR. The Cisco Gigabit Ethernet enhanced high-speed WAN interface card provides copper and optical Gigabit Ethernet connectivity through a dual-purpose uplink (DPU).
Technical Information
Application/Usage:	Data Networking
	Wide Area Network
	Optical Network
Interfaces/Ports
Interfaces/Ports:	1 x 10/100/1000Base-T LAN
Interfaces/Ports Details:	1 x RJ-45 Simplex 10/100/1000Base-T Network LAN
Media & Performance
Connectivity Media:	Twisted Pair 10/100/1000Base-T
Data Transfer Rate:	10 Mbps Ethernet
	100 Mbps Fast Ethernet
	1 Gbps Gigabit Ethernet
I/O Expansions
Expansion Slots:	1 x SFP (mini-GBIC)
Management & Protocols
Management:	QoS SNMP RMON Command-line interface
Physical Characteristics
Form Factor:	Hot-swappable
Dimensions:	0.8" Height x 3.1" Width x 4.8" Depth
Miscellaneous
Compatibility:	Cisco 1921 ISR Cisco 1941 ISR Cisco 2901 ISR Cisco 2911 ISR Cisco 2921 ISR Cisco 2951 ISR Cisco 3925 ISR Cisco 3925E ISR Cisco 3945 ISR Cisco 3945E ISR

General Information
Manufacturer:	Cisco
Product ID:	EHWIC-VA-DSL-M
Product Description:	Cisco Multi Mode VDSL2/ADSL/2/2+ EHWIC Annex M
Product Type:	WAN Module
Marketing Information
Cisco Integrated Services Routers Generation 2 (ISR G2) offer a wide variety of WAN connectivity modules to accommodate the range of application needs in customer networks. The Cisco Multimode VDSL2 and ADSL2/ADSL2+ Enhanced High-Speed WAN Interface Cards (VDSL2 and ADSL2+ EHWICs) support DSL multimode, including very-high-speed VDSL2 and asymmetric ADSL2/ADSL2+. VDSL2 and ADSL2/ADSL2+ are supported on a single WAN interface, thus providing secure, cost-effective connectivity from small businesses to enterprise branch offices. This 1-port enhanced high-speed WAN interface card (EHWIC) supports multimode DSL (VDSL2 and ADSL2 /ADSL2+) over Plain Old Telephone System (POTS) and ISDN.
Technical Information
Application/Usage:	Data Networking
	Wide Area Network
Interfaces/Ports
Interfaces/Ports:	1 x VDSL WAN
Interfaces/Ports Details:	1 x RJ-11 VDSL Network WAN
Media & Performance
Connectivity Media:	Phone Cable
Data Transfer Rate:	100 Mbps Downstream
	50 Mbps Upstream
Management & Protocols
Management:	VLAN QoS
Physical Characteristics
Dimensions:	0.8" Height x 3.1" Width x 4.4" Depth
Weight (Approximate):	3.20 oz

General Information
Manufacturer:	Cisco
Product ID:	EHWIC-VA-DSL-B
Product Description:	Multi Mode VDSL2/ADSL/2/2+ EHWIC Annex B
Product Type:	Interface Module
Marketing Information
Cisco Integrated Services Routers Generation 2 (ISR G2) routers offer a wide variety of WAN connectivity modules to accommodate a wide range of application needs in customer network deployments. The Cisco Multimode VDSL2 and ADSL2/2+ Enhanced High-Speed WAN Interface Card (VDSL2 and ADSL2/2+ EHWIC) supports DSL multimode, including very high speed DSL (VDSL2) and asymmetric DSL (ADSL2/2+) over plain old telephone service (POTS) or an integrated services digital network (ISDN). VDSL2 and ADSL2/A2+ are supported on a single WAN interface and thus this card provides a secure, cost-effective solution for a wide range of customers ranging from teleworkers and small businesses to large enterprise branch offices.
Technical Information
Application/Usage:	Data Networking
Interfaces/Ports
Interfaces/Ports:	1 x VDSL2 WAN
Interfaces/Ports Details:	1 x RJ-11 VDSL2 Network WAN
Media & Performance
Data Transfer Rate:	200 Mbps VDSL2
Management & Protocols
Management:	VLAN QoS
Physical Characteristics
Dimensions:	0.8" Height x 3.1" Width x 4.4" Depth
Weight (Approximate):	3.20 oz

General Information
Manufacturer:	Cisco
Product ID:	EHWIC-4ESG-P
Product Description:	Cisco Four port 10/100/1000 Ethernet switch interface card w/PoE
Product Type:	WAN Module
Marketing Information
The 4- and 8-port Cisco Gigabit Ethernet Enhanced High-Speed WAN interface cards (EHWICs) can reduce your company's total cost of ownership (TCO) by integrating Gigabit Ethernet (GE) switch ports within Cisco 3900, 2900, and 1900 Series Integrated Services Routers (ISRs). These low-density Gigabit Ethernet switches offer small to medium-sized business (SMB) and enterprise branch-office customers a combination of switching and routing integrated into a single device.
Technical Information
Application/Usage:	Wide Area Network
Interfaces/Ports
Interfaces/Ports:	4 x 10/100/1000Base-T WAN
Interfaces/Ports Details:	4 x RJ-45 10/100/1000Base-T PoE WAN
Media & Performance
Connectivity Media:	Category 6 UTP 10/100/1000Base-T
Data Transfer Rate:	10 Mbps Ethernet
	100 Mbps Fast Ethernet
	1 Gbps Gigabit Ethernet
Management & Protocols
Management:	CiscoWorks LAN Management Solution (LMS) RMON 1, 2 SNMPv1, v2, v3 CLI VLAN QoS Telnet
Physical Characteristics
Dimensions:	0.8" Height x 3.1" Width x 4.8" Depth
Weight (Approximate):	3.81 oz

General Information
Manufacturer:	Cisco
Product ID:	EHWIC-4ESG
Product Description:	Cisco Four port 10/100/1000 Ethernet switch interface card
Product Type:	Interface Module
Marketing Information
When inserted in a Cisco 1900, 2900, or 3900 Series ISR, the Gigabit Ethernet EHWICs provide a fully integrated, secure networking and converged IP communications solution. From a single platform with an integrated switch, you can connect IP phones, wireless access points, and IP-based video cameras to your network and power them using the IEEE 802.3af or Cisco ePoE. With the optional integration of Cisco Unified Communications Manager Express, the router can also provide call processing for the phones. As users attempt network access, the Gigabit Ethernet EHWIC can use IEEE 802.1x to validate the credentials of the end device and place the users in the appropriate VLAN or Cisco TrustSec(tm) group. As the end-user data leaves the LAN, the router can then encrypt the traffic and place it on a multitude of VPNs, securing the communications among branch offices and central sites.
Technical Information
Application/Usage:	Data Networking
	Wide Area Network
Interfaces/Ports
Interfaces/Ports:	4 x 10/100/1000Base-T WAN
Interfaces/Ports Details:	4 x RJ-45 10/100/1000Base-T Network WAN
Media & Performance
Connectivity Media:	Twisted Pair 10/100/1000Base-T
Data Transfer Rate:	10 Mbps Ethernet
	100 Mbps Fast Ethernet
	1 Gbps Gigabit Ethernet
Management & Protocols
Management:	Web-Based Management Command Line Interface SNMP v1, v2, v3 RMON 1, 2, 3, 9 Telnet VLAN QoS MIB
Physical Characteristics
Dimensions:	0.8" Height x 3.1" Width x 4.8" Depth
Weight (Approximate):	2.72 oz

General Information
Manufacturer:	Cisco
Product ID:	EHWIC-4ESG-P
Product Description:	Cisco Four port 10/100/1000 Ethernet switch interface card w/PoE
Product Type:	WAN Module
Marketing Information
The 4- and 8-port Cisco Gigabit Ethernet Enhanced High-Speed WAN interface cards (EHWICs) can reduce your company's total cost of ownership (TCO) by integrating Gigabit Ethernet (GE) switch ports within Cisco 3900, 2900, and 1900 Series Integrated Services Routers (ISRs). These low-density Gigabit Ethernet switches offer small to medium-sized business (SMB) and enterprise branch-office customers a combination of switching and routing integrated into a single device.
Technical Information
Application/Usage:	Wide Area Network
Interfaces/Ports
Interfaces/Ports:	4 x 10/100/1000Base-T WAN
Interfaces/Ports Details:	4 x RJ-45 10/100/1000Base-T PoE WAN
Media & Performance
Connectivity Media:	Category 6 UTP 10/100/1000Base-T
Data Transfer Rate:	10 Mbps Ethernet
	100 Mbps Fast Ethernet
	1 Gbps Gigabit Ethernet
Management & Protocols
Management:	CiscoWorks LAN Management Solution (LMS) RMON 1, 2 SNMPv1, v2, v3 CLI VLAN QoS Telnet
Physical Characteristics
Dimensions:	0.8" Height x 3.1" Width x 4.8" Depth
Weight (Approximate):	3.81 oz

General Information
Manufacturer:	Cisco
Product ID:	EHWIC-D-8ESG-P
Product Description:	Cisco Eight port 10/100/1000 Ethernet switch interface card w/ PoE
Product Type:	Interface Module
Marketing Information
When inserted in a Cisco 1900, 2900, or 3900 Series ISR, the Gigabit Ethernet EHWICs provide a fully integrated, secure networking and converged IP communications solution. From a single platform with an integrated switch, you can connect IP phones, wireless access points, and IP-based video cameras to your network and power them using the IEEE 802.3af or Cisco ePoE. With the optional integration of Cisco Unified Communications Manager Express, the router can also provide call processing for the phones. As users attempt network access, the Gigabit Ethernet EHWIC can use IEEE 802.1x to validate the credentials of the end device and place the users in the appropriate VLAN or Cisco TrustSec(tm) group. As the end-user data leaves the LAN, the router can then encrypt the traffic and place it on a multitude of VPNs, securing the communications among branch offices and central sites.
Technical Information
Application/Usage:	Data Networking
	Wide Area Network
Interfaces/Ports
Interfaces/Ports:	8 x 10/100/1000Base-T WAN
Interfaces/Ports Details:	8 x RJ-45 10/100/1000Base-T Network WAN
Media & Performance
Connectivity Media:	Twisted Pair 10/100/1000Base-T
Data Transfer Rate:	10 Mbps Ethernet
	100 Mbps Fast Ethernet
	1 Gbps Gigabit Ethernet
Physical Characteristics
Dimensions:	0.8" Height x 6.2" Width x 4.8" Depth
Weight (Approximate):	6.88 oz

General Information
Manufacturer:	Cisco
Product ID:	HWIC-AP-AG-E
Product Description:	AP HWIC, 2 radios( 2.4/5Ghz Radios for 802,11 a/b/g) Europe
Product Type:	Wireless Module
Marketing Information
The Cisco HWIC-AP 802.11A/B/G is Wireless LAN interface card in the HWIC (High-Speed WAN Interface Card) form factor providing integrated Access Point functionality in the Cisco 1800 (Modular), Cisco 2800, and Cisco 3800 Integrated Services Routers. Enterprise branch office and small-to-medium business customers can run concurrent services of Layer 3 routing, security, Layer 2 switching and now IEEE 802.11 wireless LAN functionality in a single platform. This combination offers ease of configuration, deployment, and management while delivering high performance, security and rich set of services.
Wireless Specifications
Wi-Fi:	Yes
Wi-Fi Standard:	IEEE 802.11a/b/g
Number of Antennas:	2
Antenna Gain:	2.2 dBi
Antenna Connector:	RP-TNC
Maximum Antenna Range:	2000 ft
ISM Band:	Yes
ISM Minimum Frequency:	2.41 GHz
ISM Maximum Frequency:	2.47 GHz
Wireless Transmission Speed:	54 Mbps
Wireless Security:	WEP
	WPA2
Management & Protocols
Security Features:	RADIUS
	AES
	MD5
Physical Characteristics
Height:	76.0"
Width:	3.1"
Depth:	4.9"
Weight (Approximate):	5.76 oz
Miscellaneous
Device Supported:	Router
Certifications & Standards:	Wi-Fi WWM IEEE 802.11a IEEE 802.11b IEEE 802.11g IEEE 802.11e IEEE 802.11i IEEE 802.1x IEEE 802.1p IEEE 802.1q FCC Bulletin OET-65C RSS-102 Safety: UL 60950 CAN/CSA C22.2 No. 60950 IEC 60950 UL 2043 Radio Approvals: FCC Part 15.247 RSS-210 (Canada) EN 300.328, EN 301.893 (Europe) ARIB-STD 33 (Japan) ARIB-STD 66 (Japan) ARIB-STD T71 (Japan) EMI and Susceptibility (Class B): FCC Part 15.107 and 15.109 ICES-003 (Canada) VCCI (Japan) EN 301.489-1 and -17 (Europe)

Specifications
Type	Fixed
Topology	Ethernet (10/100BaseTX) Ethernet (10/100/1000BaseT) Gigabit Ethernet (SFP)
Maximum Port density	8 10/100 ports
Uplinks	1 dual-purpose (10/100/1000 or SFP) ports
Modular/Expansion Slots	n/a
Architecture	Layer 2 Switching (basic connectivity), Layer 2 Switching (intelligent services), Voice Enabled
Form Factor	Fixed, Rack Mountable, Standalone/Clustering
Dimensions	1.73 x 10.6 x 6.4 in.
DRAM	64 MB
Features
Specialized Service Modules	n/a
Security
DHCP Snooping
Dynamic ARP Inspection
IP Source Guard
RP Rate Limiters
TCP Intercept
802.1x
Port Security
Dynamic VLANs
Private VLANs
Private VLAN Edge
Secure Shell
SNMPv3
Unicast RPF
ACLs (L2-L4)
Kerberos
TACACS+
RADIUS
High Availability/Resilliency
Hardware Redundancy	n/a
High Availability/Resilliency	PVST, Broadcast Suppression, Unicast Suppression, Mulitcast Suppression, Spanning Tree, Portfast, Uplink Fast, Backbone Fast, 802.1s, 802.1w
Management
Management features	SPAN, RSPAN, CiscoView, Cisco Discover Protocol (CDP), Virtual Trunking Protocol (VTP), Telnet Client, BOOTP, TFTP, CiscoWorks, CWSI, RMON, SNMP, Clustering, Web-Based Management
Scalability
WAN Interface Support	n/a
Throughput	2.7 Mpps
Backplane Capacity	16 Gbps
Number of VLANs	255

Specifications
Type	Fixed
Topology	Ethernet (10/100BaseTX) Ethernet (10/100/1000BaseT) Gigabit Ethernet (SFP)
Maximum Port density	8 10/100 ports
Uplinks	1 dual-purpose (10/100/1000 or SFP) ports
Modular/Expansion Slots	n/a
Architecture	Layer 2 Switching (basic connectivity), Layer 2 Switching (intelligent services), Voice Enabled
Form Factor	Fixed, Rack Mountable, Standalone/Clustering
Dimensions	1.73 x 10.6 x 6.4 in.
DRAM	64 MB
Features
Specialized Service Modules	n/a
Security
DHCP Snooping
Dynamic ARP Inspection
IP Source Guard
RP Rate Limiters
TCP Intercept
802.1x
Port Security
Dynamic VLANs
Private VLANs
Private VLAN Edge
Secure Shell
SNMPv3
Unicast RPF
ACLs (L2-L4)
Kerberos
TACACS+
RADIUS
High Availability/Resilliency
Hardware Redundancy	n/a
High Availability/Resilliency	PVST, Broadcast Suppression, Unicast Suppression, Mulitcast Suppression, Spanning Tree, Portfast, Uplink Fast, Backbone Fast, 802.1s, 802.1w
Management
Management features	SPAN, RSPAN, CiscoView, Cisco Discover Protocol (CDP), Virtual Trunking Protocol (VTP), Telnet Client, BOOTP, TFTP, CiscoWorks, CWSI, RMON, SNMP, Clustering, Web-Based Management
Scalability
WAN Interface Support	n/a
Throughput	2.7 Mpps
Backplane Capacity	16 Gbps
Number of VLANs	255

Specifications
Type	Fixed
Topology	Ethernet (10/100BaseTX) Ethernet (10/100/1000BaseT) Gigabit Ethernet (SFP)
Maximum Port density	8 10/100 ports
Uplinks	1 dual-purpose (10/100/1000 or SFP) ports
Modular/Expansion Slots	n/a
Architecture	Layer 2 Switching (basic connectivity), Layer 2 Switching (intelligent services), Voice Enabled
Form Factor	Fixed, Rack Mountable, Standalone/Clustering
Dimensions	1.73 x 10.6 x 6.4 in.
DRAM	64 MB
Features
Specialized Service Modules	n/a
Security
DHCP Snooping
Dynamic ARP Inspection
IP Source Guard
RP Rate Limiters
TCP Intercept
802.1x
Port Security
Dynamic VLANs
Private VLANs
Private VLAN Edge
Secure Shell
SNMPv3
Unicast RPF
ACLs (L2-L4)
Kerberos
TACACS+
RADIUS
High Availability/Resilliency
Hardware Redundancy	n/a
High Availability/Resilliency	PVST, Broadcast Suppression, Unicast Suppression, Mulitcast Suppression, Spanning Tree, Portfast, Uplink Fast, Backbone Fast, 802.1s, 802.1w
Management
Management features	SPAN, RSPAN, CiscoView, Cisco Discover Protocol (CDP), Virtual Trunking Protocol (VTP), Telnet Client, BOOTP, TFTP, CiscoWorks, CWSI, RMON, SNMP, Clustering, Web-Based Management
Scalability
WAN Interface Support	n/a
Throughput	2.7 Mpps
Backplane Capacity	16 Gbps
Number of VLANs	255

Specifications
Type	Fixed
Topology	Ethernet (10/100BaseTX) Ethernet (10/100/1000BaseT) Gigabit Ethernet (SFP)
Maximum Port density	48 10/100 ports
Uplinks	2 dual-purpose (10/100/1000 or SFP) ports
Modular/Expansion Slots	n/a
Architecture	Layer 2 Switching (basic connectivity), Layer 2 Switching (intelligent services), Voice Enabled
Form Factor	Fixed, Rack Mountable, Standalone/Clustering
Dimensions	1.73 x 17.5 x 9.3 in.
DRAM	64 MB
Features
Specialized Service Modules	n/a
Security
DHCP Snooping
Dynamic ARP Inspection
IP Source Guard
RP Rate Limiters
TCP Intercept
802.1x
Port Security
Dynamic VLANs
Private VLANs
Private VLAN Edge
Secure Shell
SNMPv3
Unicast RPF
ACLs (L2-L4)
Kerberos
TACACS+
RADIUS
High Availability/Resilliency
Hardware Redundancy	External Redundant Power Supply
High Availability/Resilliency	PVST, Broadcast Suppression, Unicast Suppression, Mulitcast Suppression, Spanning Tree, Portfast, Uplink Fast, Backbone Fast, 802.1s, 802.1w
Management
Management features	SPAN, RSPAN, CiscoView, Cisco Discover Protocol (CDP), Virtual Trunking Protocol (VTP), Telnet Client, BOOTP, TFTP, CiscoWorks, CWSI, RMON, SNMP, Clustering, Web-Based Management
Scalability
WAN Interface Support	n/a
Throughput	6.5 Mpps
Backplane Capacity	16 Gbps
Number of VLANs	255